J/80 Brochure by J/composites EU
Spars and Spare parts by Rig-Rite
Technical specifications
| Dimensions | Foot/ Lbs | Meter/ Kg |
| LOA | 26.30 | 8.00 |
| LWL | 22.00 | 6.71 |
| Beam | 8.30 | 2.51 |
| Standard Draft | 4.90 | 1.49 |
| Standard Ballast | 1,400 | 635 |
| Displacement | 2,900 | 1,315 |
| Engine | outboard | outboard |
| 100% SA | 338 | 31.40 |
| I | 31.50 | 9.60 |
| ISP | 33.00 | 10.06 |
| J | 9.50 | 2.90 |
| P | 30.00 | 9.14 |
| E | 12.50 | 3.81 |
| SA/Dspl | 27 | 27 |
| Dspl/L | 122 | 122 |
Hull & Deck Construction
- Composite hull and deck of GRP balsa sandwich with E-glass fabrics, additional reinforcing in way of highly loaded hardware.
- Vinylester and ISO NPG gelcoat in hull for osmotic gelcoat blister protection.
- Molded GRP main bulkhead to absorb the direct loads of the shrouds and mast compression.
- Mast step loads are distributed to aluminum frame fastened to the main bulkhead.
- Hull is reinforced in way of keel with several transverse molded stringers.
Deck Hardware
- Large modern cockpit with molded foot braces on centerline.
- Non slip finish to all horizontal deck surfaces in white.
- Molded Toe-rail forward.
- Bolts, screws and fitting are all made of stainless steel, marine grade anodized.
- Stainless steel forestay attachment plate.
- Stainless steel pulpit single lifeline.
- “U” bolt on the foredeck.
- Stainless steel chain plates for cap shrouds, lower, shrouds and backstay.
- Opening hatch (420 x 420 mm) mounted on cabin trunk forward of mast.
- Two black anodized jib T tracks with cars.
- Boom vang system (12:1) with swivel mounted cleats, on both sides of the coach roof.
- Mainsheet traveler with coaming mounted (2:1) control line, cleats.
- Mainsheet system (5:1) with swivel cam cleat and ratchet block on cockpit sole.
- Cleats and blocks for backstay adjustment (4:1) led forward in cockpit to port and starboard.
- Two 30:1 primary winches with cam cleats.
- Internal bowsprit launching line led aft through fairleads to cabin trunk cam cleat.
- Bullseye fairleads for furler control line (port with cam cleat) and tack line (starboard) to cabin side mounted clutch.
- Two halyard storage bags shipped loose.
- Spinnaker sheet blocks outboard of winches and aft.
- Two stern pulpits.
- Single continuous lifeline.
- One fixed cabin window on each side of cabin side.
- GRP main sliding hatch with acrylic one piece offshore drop board.
- Winch handle.
- Bow and stern running lights.
Keel & Rudder
- Low VCG keel cast from lead and antimony, faired and finished with an epoxy primer and secured by way of stainless steel bolts to the integral molded hull sump.
- Reinforced FRP rudder on transom with stainless steel fittings.
- Laminated varnished wood tiller, with adjustable tiller extension.
Spars & Rigging
- Mast and boom in anodized aluminum.
- Headsail roller furling on headstay.
- Two pairs of swept spreaders.
- Stainless steel wire standing rigging with turnbuckle adjusters.
- Backstay with adjustment tackle led to both sides of the cockpit.
- Complete running rigging package.
Outboard Motor
- Optional owner supplied, minimum 3.5hp long shaft recommended.
- Low transom suitable for direct mounting of a 3 or 4 hp outboard.
Interior
- Removable cabin sole.
- Molded settee berths with access to storage below.
- Large forward V-berth platform with two access panels above mast step.
- Large removable molded step with space for an outboard and cooler to be stored aft.
- Crane lifting bar integral to keel bolt system.
- Interior reading light.
- Electrical panel.
- Battery box with straps (battery owner supplied).